Product Details
Uses
- Varnish and protection of wood products.
- Protective coating for marine and offshore equipment.
- Surface protection of cement and concrete (ex car park, wall
- coating, warehouse floor).
- Protective coating for ceramic tile.
- Protective coating for plastic product.
- Protective coating for vehicle.
Features
- Water-base green product.
- Fast setting.
- Single component, easy to use.
- Nano size penetrating ability.
- Chemical cross-linking bonding with mostly substrate (ex: wood, stone, ceramic tile, acrylic and PU paint, plastic).
- Water vapor breathable.
Technical & Physical Data
Instruction for Use
1. Surface preparation : Ensure surfaces to be coated are clean, dry. Before applying Cireco Nano Coat NC-7 , remove all oil, grease, dust, dirt and other foreign material by using an appropriate cleaner. To ensure that the surface is completely free of oil and grease, use a lint-free white cloth with a Cireco S05 cleaner and wipe the surface. If the cloth remains white, the surface is clean; if the cloth turns dark, continue cleaning until it remains white. Once clean, NC-7 can be applied by following the instructions below.
2. Coating Application : It is recommended that coating application be performed in a clean environment to minimize surface defects. The coating can be applied by immersion, spraying, rolling, or brushing.
3. Curing :
(1) Ambient Curing
Under ambient conditions (25°C / 77°F, 50% RH) a single coat will be dry to the touch in 4 hours and completely cured in 24 hours.
(2) Accelerated Curing
Alternatively, the coating can be applied to the surface, dried in ambient air for 30 minutes, and then heated to 80 °C for 1 hour. An oven, blow dryer or heat gun may be used (maximum temperature is 150 °C). After heating, coated parts should be allowed to cool before handling.
*Application Notes :
(1) Test Area
Given the wide variety of metals and the various methods and environments of application, it is advisable to first apply Cireco Nano Coat NC-7 to a test piece or in an inconspicuous area to evaluate the resulting adhesion and appearance. There will often be some enhancement in luster (gloss) from the original surface.
(2) Clean Up
Clean tools and flush equipment immediately after application is completed with water thoroughly before product dries. Once the coating is
dry, the tools cannot be cleaned with water.
(3) Weatherability and UV Protection
For best performance, when applying to UV-sensitive surfaces (e.g., plastics, composites), apply as thick a coating as possible, and/or ensure a minimum DFT of 300- 500 microns. Select the appropriate surface preparation protocol (cleaning and/or surface treatment, priming) and test to ensure coating adhesion has been maximized. Some surfaces (e.g., certain paints, plastics and composites) may require a primer, please check with Cireco Technical center. Samples intended for weatherability testing should be conditioned for a minimum of 1 week at 25°C with at least 50% relative humidity.
Storage & Handling :
1. Precautions for Safe Handling:
Appropriate personal protective equipment should be used at all times. Provide good ventilation or extraction. Avoid prolonged or repeated breathing of vapor. Avoid contact with eyes, skin and clothing. Keep away from heat, sparks, flames and other sources of ignition. Wash hands thoroughly after handling.
2. Conditions for Safe Storage (including any incompatibilities):
Avoid storage over 100° F and contamination with incompatible materials. Keep containers tightly closed in a cool, well ventilated place. Protect from moisture. Residual vapors might explode on ignition. Do not apply heat, cut, drill, and grind or weld on or near this container.
Health & Safety
Wash both hands after work. Ensure adequate ventilation when using these products. If working in confined areas, suitable respiratory protective equipment must be used. Wear protective gloves when handling these products. The selected protective gloves must comply with the standard of EN374 or equivalent.
Eye protection should be worn. Safety glasses for side shields must be comply with EN166, ANSI 87.1-2010 or equivalent. Wear suitable protective clothing. Types of protective clothing or equipment must be selected according to the amount and concentration of hazardous materials in a specific workplace.
If contact with skin occurs, it must be removed before curing takes place. Wash off with an industrial skin cleanser followed by plenty of soap and water. Do not use solvent. In case of contact with eyes, rinse thoroughly with plenty of water and seek medical advice if symptoms persist.